5 Method of Feeder Fishing for carp in 2020

Disclosure: I earn a small commission when you purchase products through my affiliate links – read more

The feeder fishing method is an easy and efficient fishing method. The technique is common with amateur fishing enthusiasts like myself and with professionals. Carp is typically the target, so the water that has a fair carp stock works best. Lets start by looking at how fish is captured by the feeder system.

About Feeder Fishing

It is an inline feeder system or a secure feeder process. Inline simply means that the main line runs through the middle of the feeder. Safe refers to the safety of fish, which I will explain later. The feeder is flat on the ground, doing two things. 

  • First, the casting weight is provided.
  • Second, the feed is always the right one on the lake bed. That is, with the frame above. 

The feeder is attached to a short line length with the hook. Feed and the hook and bait are molded around the frame. The hook and the bait are embedded in this creates a clean food pack. If a fish passes through the feeder, it slips down to eat the food while simultaneously swallowing the bait and hook. The feeder is lifted off the river bottom as the fish lifts its head. The feeder weight that pulls the crook length causes the hook to squeeze in the mouth of the fish. If the fish feels the pickle of the hook, its a trap and a bolt, which gives the rod a clear indication. 

Usage

I use a small feeder of 24 grams most of the time. Since they are far too light and fiddly, I dont use anything less than 24 grams. Due to the risk of overfeeding, I dont use a large-size feeder. The fish dont eat their fill, so I dont want to leave the place. I use a Quiver Tip rod 11 feet which is capable of casting 30 grams. I can cast 40 meters comfortably with such a rod and a 24 gram catfish. Make sure that the weight of the feeder is always measured by your pin. I need a heavier feeder and a stronger, longer rod to cast further.

For example, a 45 gram feeder will need a 12-foot rod, but it should cast more than 70 meters. With this rod I use an eight-pound monofilament line size 40 Baitrunner reel. Some fishermen do not use mono when feeding, prefer fluorocarbon or braid fishing. The line question is important, but only what I can tell you. 

Read more: TOP 8 BEST CATFISH BAITS TO CATCH CATFISH- BLUE, FLATHEAD AND CHANNEL CATFISH   

When I fish under 40 meters I like mono because there is a certain stretch in the monofilament line. The bite on the method can be quite intense and the extension in the mono helps absorb the fish s initial lung, but it becomes too much for more than 40 yards. It feels like you try to play the fish on an elastic length. Fluorocarbon is much less stretchy and tangled, which makes it much easier to monitor the distance of fish.

But, if you hit the fish near the back, the lack of a string of fluro or twine can result in hook pulls or the length of the hook is broken.

If I use fluorocarbon or braid, I will use a light clutch setting on the reel. Before the hook pulls, the clutch strips and the line breaks. Anyway, make sure the supply, rod, cartridge and line complement each other and are balanced whatever you use. 

Preparation

SET EQUIPMENTS

The idea of a feeder is simple, but it is the trick to get the feed right and load it. First, pellets or mixing the method base into the feeder frame. The first task is to produce pellet. During castings and through the water, the food must also stay on to the lake bed. The first job I do at arrival is to prepare the feed. Put the dry powder in a pad for a method mix groundbait and add a small pond water to make a great blend and rub the groundbait back into a different pad. The lumps are the wettest areas of the rim.

By using a riddle, these weather lumps will be broken down and spread over the rest of the mixtures. You must now take a good 15 minutes to leave the bait to soak. Put some pellets into a bait box for pellets and cover them in the water of the tank. Let each millimeter of a pellet soak for one minute. Oily pellets such as healing take a long time, often a lot longer. Its up to the brand. When soaked, drain the excess water and leave for 15 minutes.

The pellets sometimes stick closer together than others. Better than large pellets, micro or small pellets stick together. You can then attach pellets to any prepared groundback in a 50/50, if the pellets you want to use dont stay together. 

Join the feeders through the feeder body by threading the main line. Attach a pivoting to the main track end. The pivot is important and specific to the feeder, although most feedingstuffs include the pivot. Push the pivot in the feeder body once tied. It should fit snugly into the feeder front. Use a short shank wide-gage hook to ensure the best chance of hooking a fish. This model hook is really hooky when you see what I mean and most probably picks up or catches in the mouth of a fish. The bait is generally attached to it via hairstyle, so that the hook is fully exposed. Using a band to fasten the bait for hard apples like pellets. Use your hair with a hair stop for softer coats such as boilies. 

Its a few pounds, and bigger, I want to catch fish. I use baits with barbless hooks of 16 to 12 scale up to around 10 millimeters. Using a beardless hook at all times. They not only penetrate easier, but are also more childlike to fish. I tie my own hook lengths, normally 6 pounds of mono but a low-diametric modern thread, all tissue, might be better, or you can buy prefabricated tackles feeder hook lengths. I tend to use a hook long with a more weak breaking strain, because the weaker hook length is more likely to break off than the main strain if the line is under a great strain. If a sharp underwater object somehow breaks down the main line, the safe aspect of the safe method feeder comes into play. 

The snug-fitting swivel that has been connected to the hook length is removed from the feeder by means of a secure feeder, allowing the remaining main line to pull into the feeder. This ensures that the fish are not linked to a heavy feeder that could kill the fish. Always use a secure feeder and correctly set the attachment of your roll even with a weaker hook duration. Arrange the width of the rod so that the rod is in a swimming angle. It doesnt have to be in the right angle, but in the right perspective. The rod tip should be near the surface of the water. This ensures the first few feet above the feeder are near the ground, where the fish will hopefully not notice them. As I like using a rear rod that grips the rod when the hook is pinched, I have less chance that the rod is pulled in. While it is easier to hold the rod in your lap if bites come quickly. 

CHECK THE FEED

I will check the feed once all equipment is set. Its too dry on the ground. You can see that it squeezes in a ball, but it only crumbles as soon as I touch it. Ill have to add a little more water, mix again, riddle and leave for another 15 minutes. The pellets adhere to each other. They re about right. Theyre right. 

GO FISHING

Carp sometimes finds itself in and around reeds, lily coats, roaming an island s banks. Throw as close as you dare to a function. Just try to get into a yard. If youre short or cloudy, estimate the distance and roll in or line up correctly. Clip up, then. Cast another test and adjust it fine. When winding back the feeder, count the number of turns it takes to pick up the feeder. It is easy to set the distance again if you have to unclip for any reason. Cast a similar distance from your swim anywhere in the lake. Clip up and reel down and count a few turns. If you dont have the correct number of turns, cast them out again, then wind in or wind out until you have the correct number of turns. Clip again, you know that the right distance is established. 

Usually I dont use a line clip when Im fishing in open water. I am afraid that before it reaches the clip of the line and breaks the line, I can not stop a big fish, but the fish are swimming to one side rather than to one another right up against an island or shed beds. There are carriages that unclip automatically, but I dont have one, so I just dont have an open water clip. I would attach the hook length while I was happy with the distance and clipped up. Its relatively appropriate that a short four-inch hook length is best, so the fish can suck it into their mouths long enough, but short enough for the fish to grab as soon as it moves. 

A hook length of four inches, for me, is four inches from the hook bend to the end of the loop. The bait on the hair, right outside of the base of the hook, I tie my hook lengths. Use the hook with a knotless knot and the loop eight knots. I will include a pellet band on my hair if I use a hard hook bait like a pellet. I just would leave the loop in my hair with a soft bait or boilie, for example, and then wear a boilie stop or, I think, better still a blade of grass to continue the bait. Finally, I connect the length of the hook on the feeder and cross the loop through the pivot. 

Read more: BEST FISHING PLACE IN THE WORLD IN 2020

NOTE

When pressed, the ground should not crumble like before in lumps. This is ready to be used now. I could squeeze the feed by hand, but using a mould is much easier. In the bottom of the mold, place the hook and bait. Press the mold into the mold and fill with feed, first frame. Squeeze the feeder, press the bottom of the mould to throw the loaded feeder. Its just the same with pellets. Fold the hook bait down, feed up, pull the feeder into the mould. The feeder will inevitably be washed away as it falls through the water. If the water is more than 6 feet deep, the feeder may need to skin to ensure that the hake bait is not cleared. 

Skinning just loads the feeder as normal and adds an additional foot layer to the top. As the feeder sinks, the skin keeps the bait in place. Skinning can also help you get plagued by fish that eat the food. You can keep your feeder in the swim several minutes longer by feeding your skin. 

Each bottom and pellet type takes a different quantity of water. It is possible to add additional water to the ground bait and for a second time, just for a minute or two, if it is too dry, but once either becomes too wet, not only does the feeder have trouble loading but also how the feeder works in the water. The pellets stick inside the feeder mold here. The pellets are too wet because of that. 

Before I drained them off, I left them drinking too long in the cold. Groundbait also would stick to the mold if there is added too much water to the mixture. I mix 50/50 pellets with groundbait only if the pellets are too wet. This lets them sit with the feeder as you can see. There are several tricks with the too wet ground bait, like putting the mold in a polythene bag and loading the feeder on top or first moistening or adding more dry mix to the bait. But to be honest, it is the best solution to spend a little time mixing it up

CAST STEP

I can rely on the feeder being loaded and I can rely on the feed not to fly or decompose when it reaches the water. I just cast past my selected location, since I know the long clip will stop the feeder at the appropriate distance. Cast and hold the rod straight to absorb the clip shock that stops the feeder. Done correctly, just before it reaches the water will the feeder give a tug on the rod. 

  • FEEDER ON THE BOTTOM

Once the feeder is set on the floor, sink the main row by slowly winding in, pulling the rod under or holding the rod tip below the water and drawing the rod by hand. Finally, clamp the feeder down and create a slight curve in the tip of the quiver. Especially when you sink the line, you dont move the feed. Every movement causes the feeder to dig into the mud or causes the feeder to turn around, which does not catch any fish for you. Im sure you will appreciate with the feeder on the bottom that it will not last long. Roach can demolish your feed quickly and carp actions are about to wash the feet away, but how long do you have to leave the feed before recharging it? 

Perhaps the easiest way to respond is by doing what I do when I fish for the feeder method. I like first leaving the feeder for just five minutes in the first six casts in the summer, when I know that the fish is most involved. I at least have some feed into the swim if I do not catch anything, which I hope will attract a couple. SAM AND MARY will then leave the feeder on each cast for ten to fifteen minutes until the fish arrives. I leave time in the feeder after I start catching it, because Ill reload them after each fish.

avatar I’m Fabian, aquarium fish breeder and founder of this website. I’ve been keeping fish, since I was a kid. On this blog, I share a lot of information about the aquarium hobby and various fish species that I like. Please leave a comment if you have any question.

Related Articles

Leave a Reply

Your email address will not be published. Required fields are marked *